11/26/2022 0 Comments Rooftech airmount![]() ![]() We were very impressed with these mounts and have recommended the AIR mount system to several others in the process of designing roof-top systems already (all DIY'ers such as us). The inspectors complimented the installation stating that it was very neat and solid. Although initially it was feared that it might be an issue (due to the non-alignment to rafter locations), in the end it was a total non-event. RT-MINI is engineered to withstand wind speeds up to 180 mph and ground snow up to 90 psf. The signed PE letter (California in this instance) was a critical key in gaining acceptance with the permit engineer and inspectors. (858) 935-6064 The RT-MINI with AlphaSeal RT-MINI is Roof Tech’s Self-flashing mounting base designed to attach conventional rail mounting systems and accessories including the conduit. The instructions were very clear and concise and helped immensely. It was made simple by the bonding method and panel spacers that were part of the edge and middle mount system component kits. Fastening the panels to the mounts was similarly easy. #ROOFTECH AIRMOUNT DRIVER#Use of a cordless impact driver as shown in their informative videos is highly advised. #ROOFTECH AIRMOUNT INSTALL#We were able to install 40 mounts (for two horizontal rows of nine panels each) in a single morning. S-5® Products manufactured by Metal Roof Innovations, Ltd. The installation could not have been simpler or faster. RoofTech GmbH exclusively distributes special products for fastening in the European roof market. Rack-less design reduced the overall cost and complexity but also reduced the weight loading on the roof system as a whole, which was reflected in the permit calculations. The idea of rack-less installation was also very appealing to us as we live in a windy location and the E(AIR) system worked beautifully, keeping the panels low to the roof surface without resorting to wind skirts and deflectors. However of greater importance the horizontal placements could be located at the ideal locations for the panel widths. The vertical locations of the mounts could be placed as needed to match up with the slip-stopper brackets on the panels, as would have been the case with rafter-aligned systems of course. This method was also particularly important to us because we installed the PV panels in a portrait orientation. The Roof Tech system was a huge benefit in being able to locate the array properly to achieve regulatory clearances and access. Rooftech Roofing Flat Roofs in Qualicum Beach 5-3175 Brooklin Lane, Qualicum Beach, BC V9K 1X5, Qualicum Beach. The Roof Tech system allowed us to install the mounts in their ideal locations essentially without regard to rafter locations. These things rendered the rafter locations inaccessible by any normal means other than exploratory drilling (which we were not willing to do). This was because due to an unusual roof line, foil-faced sheeting, skip sheeting under that, and a cathedral ceiling interior. Without them we almost certainly would not have even attempted the installation. and five provinces in Canada.Roof Tech AIR mounts were the deciding factor in our decision to self (owner) install our PV system recently (July 2017). Stamped PE letters are available for 40 states in the U.S. #ROOFTECH AIRMOUNT CODE#RT-MINI II is fully waterproof and certified by the International Code Council (ICC-ESR 3575). As a result, there is no damage to the seal on asphalt shingles. The main difference between RT-MINI II and conventional flashing is the faster installation time because RT-MINI II is fastened with wood screws, eliminating the need for pilot holes. RT-MINI II is engineered to withstand wind speeds up to 180 mph and ground snow up to 90 PSF. The new design uses less aluminum, making it a more efficient design that reduces raw materials and decreases logistic expenses. Fall is typically the best season for roof repairs or to replace an existing roof, and each year we install hundreds. Whether they are affordable re-roofs or more complex solar panel installations on steep pitch custom homes, we take care of it all. The optional RT 5 x 90mm stainless wood screws (rafter only) can provide a wider span, and the offset rafter mounting adds more options on any style of roof and pitch. Over the past several years, the RoofTek team has completed thousands of rooftop installations. The RT-MINI II has more mounting options for rafters and also combining rafter and deck attachments. The RT-MINI II is designed to attach conventional rail mounting systems for any sloped roofs consisting of metal, EPDM, TPO, and asphalt. The optional RT 5 x 90mm stainless wood screws (rafter only) can provide a wider span, and the offset. ![]() The RT-MINI II is our most popular residential roof mount base featuring Roof Tech Inc's Self-flashing AlphaSeal™ PV Mounting Technology. The RT-MINI II is designed to attach conventional rail mounting systems for any sloped roofs consisting of metal, EPDM, TPO, and asphalt. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |